Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 9 - Jul 14
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Breathe Right Neusstrips clear 30.00 StuksBreathe Right Neusstrips clear Breathe Right Neusstrips Gevoelige Huid Small Breathe Right neusstrips helpen vrij door de neus te ademen. De neusstrip is een huidvriendelijke kleefstrip met twee buigzame strookjes waarmee je de strip over de neusbrug kunt plakken. De neusvleugels worden op zachte wijze open getrokken waardoor je meer lucht krijgt en de ademhaling soepeler verloopt. Hierdoor kan het snurken verminderen of zelfs helemaal verdwijnen.
Breathe Right Neusstrips clearBreathe Right Neusstrips Gevoelige Huid Small
Breathe Right neusstrips helpen vrij door de neus te ademen. De neusstrip is een huidvriendelijke kleefstrip met twee buigzame strookjes waarmee je de strip over de neusbrug kunt plakken. De neusvleugels worden op zachte wijze open getrokken waardoor je meer lucht krijgt en de ademhaling soepeler verloopt. Hierdoor kan het snurken verminderen of zelfs helemaal verdwijnen.
Breathe Right neusstrips openen de neus tot wel 38% beter dan neussprays. Uit onderzoek is gebleken dat 90% van de gebruikers profiteert van een betere slaapkwaliteit met als positief gevolg dat er overdag beter gepresteerd wordt. De neusstrips zijn ook ideaal als prestatieverhogend middel voor sporters. De strips zijn verkrijgbaar in verschillende maten en zijn er voor de normale of gevoelige huid. Deze strips zijn voor de gevoelige huid en hebben de maat Small.
- Verbetert de ademhaling door de neus
- Vermindert het snurken
- Draagt bij aan een goede nachtrust
- Biedt verlichting bij verkoudheid en allergieën
- Ideaal als prestatieverhogend middel voor sporters
- Neusademhaling heeft een positieve invloed op een goed immuunsysteem, de gemoedstoestand en de bloeddruk
- Makkelijk te verwijderen
Gebruik
Helpt vrij door de neus te ademen, vermindert snurken en bevordert de nachtrust. Ook ideaal bij verkoudheid, allergieën en bij het sporten.
Aanwijzigingen voor gebruik
Stap 1: Was en droog uw neus. Stap 2: Verwijder de beschermstrip en plaats de neusstrip over de breedte, op het midden van uw neus. Stap 3: Wrijf de strip zachtjes vast. Stap 4: U kunt de neusstrip achteraf gemakkelijk verwijderen. Maak de eindjes los en duw dan beide zijden voorzichtig op. Dit wordt gemakkelijker wanneer de strip nat gemaakt wordt.
Medisch hulpmiddel. Lees voor gebruik de bijsluiter.
Verantwoordelijk voor het in de handel brengen
The OTC Lab Healthcare BV
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.2 ★★★★★
Based on 433 reviews
Sort
Product Reviews
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024