Hocus Pocus (owl)
SKU: 96422937663

Hocus Pocus (owl)

Sale price$16.20 Regular price$18.00
Save 10%

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 9 - Jul 14

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Hocus Pocus (owl)Our shirts are made using a high quality screen print. I press these personally using a commercial grade heat press. The finished product is extremely durable, just as if the shirt had been freshly screen printed! To insure lifetime of the item, machine wash cold , with the item inside out and warm dry recommended, no iron on dedign. Want it in a different style of garment tank, long sleeve? or a different Color? I have those too ***Please be aware

Our shirts are made using a high quality screen print. I press these personally using a commercial-grade heat press. The finished product is extremely durable, just as if the shirt had been freshly screen printed!

 To insure lifetime of the item, machine wash cold , with the item inside out and warm dry recommended, no iron on dedign.

 • Want it in a different style of garment tank, long sleeve? or a different Color?I have those too 

***Please be aware that some color choices may not always be readily available, as we face some uncertainties with suppliers in this hard time. I will do my best to accommodate your choice, please list a backup color in case I run into limited stock. 

 These are unisex shirts and run slightly larger. They are made of ring-spun cotton (and is oh soft and comfy). For women, if you prefer a looser fit, order the size based on your measurements. If you prefer a slim, form fitting fit, consider ordering 1 size down. Everything does shrink a tiny bit when you wash it, but they are cut and prepared to reduce the shrinkage so shrinkage is minimal.

-Heather shirts - 50/50 cotton poly. Super soft

 -Retail fit, Side seamed,Tear away label, unisex sizing, pre-shrunk

(in inches) XS S M L XL 2XL 3XL 4XL

Body Width 16 ½ 18 20 22 24 26 28 30 N/A

Body Length 27 28 29 30 31 32 33 34 N/A

This is a Digital mock up of my actual product so the color may be slightly different due to different computer screens 

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 96422937663

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.4 ★★★★★
Based on 943 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
P
Verified Purchase
Peter Schott
Waukegan, US
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
S
Verified Purchase
Steve M.
Bozeman, US
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
N
Verified Purchase
Nancy filippi
Port Orchard, US
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
R
Verified Purchase
rich911s
Birmingham, US
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
G
Verified Purchase
Greg
Draper, US
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024

recommand products